5KM/10/20KM Electric Fence Solar pulse Charger Controller Animal Horse Cattle Poultry Farm Shepherd Alert Livestock Tool

How the electronic fence works
Working principle of electric fence is to make animals in produce apsychological barrier, thus animal fear near the electric fence has sent to a system

of electrical impulse current frequency of once per second sent to fence line, whenthe animals hit a fence, animal fence and the ground form a loop at the same time by the safety of the shortness of a shock, Enough to make the shock animals lifetime in memory, which have the effect of control animals out and protection

fence, as a result of the action of electric fence is to make animals have a psychological barriers, fences don’t need very strong can thus should play a role,

but in design and building fences, should be the root of good design and construction, Allowing the pressure from the animals to be absorbed and relieved by snow and strong winds. The power of the electrical pulses provided to the length of the fence should be large enough to have a controlling effect.

Electric fence use and benefits

Perhaps the most widely recognized method of animal control is the electronic fencing system. Electronic fencing is not only for the control of domestic

animals and livestock, but also for a number of important uses, including: keeping wild animals out of fences, isolating animals from different groups of animals,

allowing animals to be used for grazing, Keep animals away from trees, rivers, roads, and damaged soil. Electric fencing has led to new grassland management

techniques, and better grassland management is more profitable for herders. Fixed-fixed and movable electric fences are used in the zoning of grasslands to ensure

the uniformity of grazing and animals on the grasslands. Only in this way can the grass be kept fresh and palatable, and the grass be kept at the right height, which

ultimately increases the yield of milk and meat in the grass。

Please read this manual carefully before installation and be sure to follow the following safety instructions

1 The machine must use a single leakage protector power supply, or separately installed a single leakage protector.

2 do not let the elderly and children with mobility difficulties close to the high voltage power grid 。

3 The ground wire must be connected well, the ground wire is a discharge circuit, and plays the role of safety protection, so it must be firmly installed,Open circuit or joint serious rust are easy to cause damage to the machine or leakage protector trip 。

4 The machine is not suitable to be used in humid environment. It should be installed in dry and ventilated place. Special tips: any unauthorized use of ground wire and leakage protector, causing machine damage or people and animals electric shock, the consequences.

Front pane

（2）batter cllp
(1) Power transformer

(1) Power transformers are used for 220V AC and mainframe connection 。

(2) Battery connection line. Use this line to connect the main machine when using the battery。

(3) Alarm, the sound of a siren when the fence is malfunctioning 。

(4) Power indicator light of main engine. When the light is on, the power supply is on 。

(5) High Voltage Pulse Indicator. When normal, the light flashes, indicating that the pulse is

working normally 。

(6) Failure light. This light indicates that the fence or main engine is out of order。

(7) The input voltage and quantity display meter can display the voltage and quantity of power supply or battery in real time. When the display is lower than 11V, the machine will alarm and stop working so as to protect the battery from over-discharge.

(8) The grounding terminal is connected to the earth through the wire grounding pile。

(9) 8KV positive voltage output terminal, and the grounding terminal to form 8KV high voltage brigade impulse 。

(10) High voltage positive 12kV output terminal, and the grounding terminal to form 12kV high voltage pulse electricity 。

【Rear panel】

(1) 12V DC input socket, need to use no less than 2A 12V power supply, can also use the machine equipped with the battery cable to directly use 12V battery power

supply, if the use of 220V AC, need to use the power converter (machine equipped), 220AC power must be equipped with leakage protector, or to the machine’s power converter separately installed small current leakage protector 。

(2) Pulse cycle adjusting knob. Rotating the knob can adjust the pulse to form a discharge cycle between 0.75 s and 0.3 s。

(3) Alarm output socket, alarm output 12V, used to connect the power of the alarm is less than 10W, if you need to connect the alarm is greater than 10W need external relay control power supply to the alarm, directly connected to the alarm is greater than 10W will burn out the inside of the line, our company does not bear the loss caused.

【The installation guide】

Pre-boot Steps:1 Good earthed 2 Connect the high voltage output wire 3 Pulse to the middle position 4 boot Power transformer Ground wire Hit the ground with iron

drill not less than 1.5 meters deep Power indicator will light up after startup, and then the pulse indicator will start flashing, while the output high voltage. The failure light changes from on to off, indicating that it is normal. If the failure light is long and accompanied by an alarm sound, Indicate that the fence or the high voltage connection line has the leakage place, should check and eliminate

【New machine test】
1 boot：Put the machine on the table, connect a 20cm long wire (for high voltage test) to the grounding terminal of the machine, put the pulse knob in the lowest state, and then switch on the power. At this time, the power indicator lights up (indicating that the power has been connected) and the pulse indicator lights up and flashes at the same time, and a slight knocking sound is sent out inside the machine. It indicates that the high voltage circuit is working normally 。

2 High voltage test：After starting up, the idle end of the wire on the wire terminal slowly contacts the high voltage output terminal. When the wire is about 0.5 cm away from the high voltage terminal, the high voltage electric spark will be generated. At this time, the high voltage output is normal.

Note: the inexperienced can find a dry chopstick or plastic stick, tie the wire to the chopstick and then touch the high voltage output terminal, to avoid being shocked.

3 Alarm test：Boot after working normal pulse, the pulse knob on the slow state (the highest alarm sensitivity) at this time, slowly contact with test lead to high voltage output terminals, when continuously produce two edm, alarm circuit is triggered, the alarm and alarm horn failure indicator light, when the wire away from the high voltage output terminals, Alarm stop, pulse knob as for the fastest state of the alarm test, continuously produce 7 discharge sparks, the machine alarm, the wire far away fro the output end of the alarm stop, indicating that the alarm function is normal.

Note: alarm trigger sensitivity and pulse speed has a relationship, the slower the pulse is the higher the alarm trigger sensitivity, vice versa

【Troubleshooting method】